Describe the process for cleaning of redwood viscometer
Answers
Answer:
CLEANING YOUR VISCOMETERS
Clean viscometers are essential if precise and accurate measurements are to be made. Because CANNON receives a significant number of requests for advice about cleaning methods, we offer the following instructions as a guide to cleaning most glass capillary viscometers.
Removing the test sample from the viscometer
The first step in cleaning is to remove the bulk of the test sample. For low viscosity liquids, the viscometer may be turned upside down and allowed to hang while the test sample drains into a trough. For high viscosity liquids, the sample may have to be drawn out under vacuum. The material remaining in the viscometer must then be removed by flushing with a suitable solvent. Distilled water is an obvious choice for aqueous solutions.
Petroleum-based lubricants and asphalts can usually be dissolved with light naphtha, heptane, octane, highly aromatic solvents, and many other petroleum-derived solvents. Varsol® is a commercial solvent that works very well for this purpose. For some types of samples it may be difficult to find a suitable solvent.
Highly viscous samples will not easily pour from the instrument nor do they respond well even under vacuum. The best approach is to lower the viscosity by heating the instrument in an open oven or with a stream of hot air.
Simply inverting the instrument and suspending it in an open oven over a receptacle to catch the sample usually works well. Another method is to draw the bulk of the sample out while the instrument is at an elevated temperature in a constant temperature bath. This method works particularly well for certain viscometers (such as the Zeitfuchs® Cross-Arm viscometer), as the entire cleaning can be performed while the viscometer remains fixed in the constant temperature bath. CANNON often places viscometers in an open aluminum oven (2" wide x 7" long x 5" deep), maintained at an elevated temperature, during the cleaning procedure.Even after the bulk of a viscous sample has been removed from the instrument, dissolving the rest of it may pose a considerable problem. We have found that a mixture of octane isomers is especially effective in removing the last traces of high viscosity standards from viscometers.
Drying the viscometer after cleaning
The viscometer must be completely dry before another sample is loaded. Highly volatile solvents are recommended for cleaning since any remaining solvent will evaporate quickly after the sample has been flushed from the viscometer. Often, however, the best choice of solvent for the material in the viscometer is not especially volatile. In this case, a second highly volatile solvent, which will dissolve the first solvent, can be used for the final step in cleaning. Acetone is commonly used as the second solvent because of its high volatility and its ability to dissolve traces of petroleum solvents and water. A low velocity stream of clean air will be sufficient to evaporate remaining traces of a volatile solvent, but be aware that rapid evaporation of these solvents can cool the surface of the glass to such an extent that humid air may be brought below the dew point, causing a film of water to form on the inner surfaces of the viscometer. Heating the air being drawn into the instrument or heating the glass itself will usually overcome this problem.
Cleaning insoluble deposits from viscometers
Capillary viscometers are often used to measure materials which leave stains or significant deposits of material insoluble in normal cleaning solvents. The most common approach for removing this material involves filling the instrument with a chromic acid cleaning solution and allowing the instrument to soak in the acid for up to 24 hours. Chromic acid solutions are strongly oxidizing and will convert many materials to a soluble form. Chromic acid will not attack the borosilicate glass of the viscometer and thus will not alter the calibration constant. Proper procedures must be followed when using and discarding chromic acid since it is a hazardous material. A commercially manufactured oxidizing reagent (Nochromix®) is chromium-free and may be substituted for chromic acid solutions. Nochromix is available from CANNON. Beware of glass cleaners with a high pH. Changes in viscometer calibration as great as 20% have been observed due to the prolonged use of alkaline cleaning solutions. If alkaline cleaning solutions with a pH greater than 10 have been used, the viscometer calibration should be verified to ensure that there has not been a significant change. Insoluble particles stuck in the capillary of a viscometer can sometimes be dislodged by using an ultrasonic cleaner.