describe an experiment to demonstrate that water absorbs heat on boiling
Answers
Answered by
0
water at 100 degree absorbs heat ....at this stage state of water changes to steam and thus heat is aborbed in this activity and it be confirmed by thermometer .....
the thermometer will show 100 degree all the time ....means no heat is increasing ....all heat is absorbed.....
MARK AS BRAINLIEST.....
the thermometer will show 100 degree all the time ....means no heat is increasing ....all heat is absorbed.....
MARK AS BRAINLIEST.....
Answered by
1
Hi,hope this helps you...
Procedure:
1)Take about 25ml of distilled water in a boiling tube and add 2-3 small pieces of pumice stone.
2)Close the mouth of the boiling tube with a rubber cork that has two bores and clamp it with the stand.
3)Introduce a thermometer (temperature range -10 to 110°C) in one bore of the cork of the boiling tube. Keep the bulb of the thermometer about 3-5 cm above the surface of the water.
4)Then introduce one end of a delivery tube in the second bore of the cork.
5)Place a 250ml beaker below the second end of the delivery tube to collect the condensed water.
6)Heat the boiling tube gently, preferably by rotating the flame.
7)Note the temperature (t1) when the water starts boiling.
8)Continue to heat the water till the temperature becomes constant, and the water remains boiling. Note the constant temperature (t2).
9)Record your observations in tabular form.
Note: Pieces of pumice stone are added to water before heating to avoid bumping of liquid when the temperature rises. When water boils it releases energy as bubbles. If the bubbles do not form, the water can super heat and possibly explode. This could happen if the container is very clean and there is no means for the formation of bubbles. Adding pieces of rough stone gives lots of surface area for bubbles to form and release the energy gradually.
Observations:
Record observations in the table given below:
Temperature when the water Boiling point of water
Starts boiling t1 (in °C) Continue to boil (Stationary temperature) t2 (in °C) (t1 + t2)/2 (in °C)
Inference:
The boiling point of water =_______°C
Precautions:
1)The bulb of the thermometer should be kept about 4-5 cm above the surface of water.
2)Pieces of pumice stone should be added to water before heating to avoid bumping.
3)Heating of water should be done by rotating the flame.
4)Note temperature by keeping your eyes in line with the level of mercury.
Procedure:
1)Take about 25ml of distilled water in a boiling tube and add 2-3 small pieces of pumice stone.
2)Close the mouth of the boiling tube with a rubber cork that has two bores and clamp it with the stand.
3)Introduce a thermometer (temperature range -10 to 110°C) in one bore of the cork of the boiling tube. Keep the bulb of the thermometer about 3-5 cm above the surface of the water.
4)Then introduce one end of a delivery tube in the second bore of the cork.
5)Place a 250ml beaker below the second end of the delivery tube to collect the condensed water.
6)Heat the boiling tube gently, preferably by rotating the flame.
7)Note the temperature (t1) when the water starts boiling.
8)Continue to heat the water till the temperature becomes constant, and the water remains boiling. Note the constant temperature (t2).
9)Record your observations in tabular form.
Note: Pieces of pumice stone are added to water before heating to avoid bumping of liquid when the temperature rises. When water boils it releases energy as bubbles. If the bubbles do not form, the water can super heat and possibly explode. This could happen if the container is very clean and there is no means for the formation of bubbles. Adding pieces of rough stone gives lots of surface area for bubbles to form and release the energy gradually.
Observations:
Record observations in the table given below:
Temperature when the water Boiling point of water
Starts boiling t1 (in °C) Continue to boil (Stationary temperature) t2 (in °C) (t1 + t2)/2 (in °C)
Inference:
The boiling point of water =_______°C
Precautions:
1)The bulb of the thermometer should be kept about 4-5 cm above the surface of water.
2)Pieces of pumice stone should be added to water before heating to avoid bumping.
3)Heating of water should be done by rotating the flame.
4)Note temperature by keeping your eyes in line with the level of mercury.
Similar questions